Reasons Your Fiat 500 Key Fob Won't Work

A fiat key fob replacement 500 key fob makes it simple to open doors and start your car. However, there are a variety of reasons the fob could stop functioning. This could be due to a dead battery or water damage, receiver modules issues, and interference.

This listing is for an NEW replacement Fiat Flip Key Remote - similar to the Ilco brand that needs to be professionally programmed by a local automotive locksmith (click here for Locksmith Search). Includes lock, unlock, and trunk buttons.

Dead Coin Battery

The most frequent reason why your 500 key fob doesn't function is due to the battery is dead. Modern key fobs have a limited range of operation and must be within only a few inches from the vehicle to work. If you are far from your vehicle, and you press the keyfob button, it will not respond, and display the message "Key Fob Not Detected".

If this happens, replace the battery of your coin cell (Part number CR2032) with a new one from a reliable brand like Panasonic, Duracell, or Energizer. They can be found in the local hardware store or on the internet.

After you've changed the battery on the coin cell It is possible to test it by standing next to your Fiat 500 and pressing the buttons. The car should blink its parking lights, and the key fob should work the lock and unlock switches.

If your key fob still isn't working after replacing the battery, there may be water damage that has prevented it from connecting to the module in your vehicle. Water damage can occur in a number of ways, from a light splash to submerging the fob salt water at the beach. If you suspect your fob has been exposed to water, try putting it in a dry rice bag to pull the moisture out. If this doesn't work your fob may need to be reprogrammed by an experienced auto locksmith or the dealer.

Water Damage

While the fob comes with rubber seals that keep water from the electronic chip inside the device, submerging it into the ocean or washing it in a machine can cause water damage. Saltwater is especially dangerous to the fob's circuit board and can cause it to short out and eventually die. In the event that you let your fob get wet, it's not an option but if you drop it into the water in a cup or fail to take it out of your pants pocket before running the washer Don't give up hope.

Take the battery off first. Clean the electronic chip using isopropyl ethanol or a similar product and then dry it completely before replacing the battery. Test the fob next to determine if it's working. If the fob doesn't work, it may need to be reprogrammed. This is usually done by an auto locksmith or dealer.

If the key you have is older and not programmed for your car it is necessary to replace it completely. A professional automotive locksmith can do this job. The locksmith must cut the key to match the ignition of your car. The locksmith also needs to program your fob into the car's system. This is a simple and cost-effective procedure which can be completed in the next day.

Receiver Module Issues

One of the most common reasons why your 500 key fob could stop working is that it's simply out of range. The remote has a range of 30 feet. So in the event that you are far from your car it won't respond to your commands. This can easily be resolved by moving it closer to your vehicle until it starts responding.

If your fob isn't working after you replace the battery inside the coin, which is also known as a "button", "watch" or "button" it could be due to an issue with the internal circuit board. Reprogramming the fob usually resolves this issue. You can find instructions on how to do this on the majority of vehicles by searching YouTube or checking out the owner's manual.

It could be necessary to replace the metal clips that hold the coin batteries in the correct position. If they loose tension, it could hinder the coin battery from being seated properly and can result in the malfunction of your remote.

In rare instances, the fob can become out of alignment with your vehicle because of hardware or software issues. This could cause a significant trouble, but you could usually resolve this issue by visiting a local dealer or auto locksmith to have them reprogram your fob. In certain situations they may have to reinstall the program in your body control module too.

Interference

In addition to a dead battery on a coin The key fob may not be receiving or transmitting an signal due to interference. This could happen when the keyfob's location is in close proximity to a radio transmitter like a cellphone or radar detector. The key fob might not function due to a bad connection to the buttons water damage or damage to the internal chips.

If your key fob suddenly stopped working, or if you have tried everything at home to fix it (e.g. You could have a malfunctioning 500 receiver module if you've tried replacing the battery, reprogramming it, or using a spare key fiat 500 abarth key fob replacement 500 (Click at Lifeisnew) key fob. The receiver module is located under the dash and is able to pick up the radio frequency signals from the key fob. It converts the signals into electronic commands which are then processed by the vehicle.

There is a straightforward method to reset the 500's on-board system including the keyfob. Disconnect the battery for 15 minutes, removing first the negative cable, then the positive cable. Then, reconnect the battery. This will remove any remaining electricity and restart the car's computers, which can help you get your key fob working again. If the problem persists it is recommended that you consult an expert certified technician. They'll be able to diagnose the exact cause of your problems.