How to Replace a Kia Sportage Replacement Key

For many 2018 kia sportage replacement key models keys, there is the keyless entry system that is built into the key. This key typically resembles an remote control, and is able to be replaced by a new one purchased from a kia picanto spare key dealer or a locksmith.

Key fobs may stop working due to a variety of reasons, including an empty coin battery worn buttons signals, water damage, signal interference and a faulty receiver module. Here are some helpful tips on how you can get your Kia Sportage replacement key working again.

How to replace a remote key or a smartkey?

No matter if your Kia is equipped with an intelligent key, remote key push to start key or a regular non-transponder steel key The battery inside these keys will eventually need replacement. This is particularly true if the car displays a message indicating that the smart or remote key has a low battery.

This is a relatively simple process. To replace the battery on the keyfob remove your mechanical key from the slot at the back of the fob. Then, pull the cover off. Inside the key fob, there will be the small screw that holds the battery in the correct position. Take out the old battery by removing the screw using a small screwdriver. Then, insert the new and close the slit on the key fob.

When the key fob is equipped with an updated battery and you've tested it, press the locks and unlock buttons. If the doors unlock and lock as expected, then you're all set! You can now make use of Kia's hands-free lock/unlock function whenever your fingers get chilly or you have to go on errands around Brandon.

Note: Certain key fobs (transponder chip or smart keys) may require their programming completed. This requires a specific programming machine that only the dealer or locksmith has access to. Other keys (non transponder keys made of steel) do not require programming. If your key needs to be programmed again, you will need to be aware of the number stamped on the tag that identifies the key and keep it in a safe location.

How do you replace the battery?

If your kia sorento key replacement key fob is not responding to pressing the lock or unlock button on the fob, this is a signal that the battery needs to be replaced. A low battery can also cause other issues, such as the check engine light turning on or the engine not running correctly. It is relatively easy to replace key fob batteries by using only a few simple tools.

Before you begin the process ensure that your vehicle is off and all doors are shut. Locate the small metal or plastic piece on the bottom of your key fob, and gently jiggle it until the metal key is released. The key can be put into the driver door handle to unlock your car.

To replace the battery inside the key fob, take off the cover on the rear. Utilize a plastic plier tool to remove the latch that holds the black negative cable. Remove the old battery and orient the new one in a way that the "+" positive side faces you, and the "negative" negative side is facing towards the fob's metallic electrical contacts. Push the new CR2032 battery straight into place, avoiding excessive force to avoid bending or damaging the contacts on the metal.

Once the new battery has been installed, turn the key fob off and then turn it on in the ignition for a few times until the door locks. Then you can test your Kia key fob and see if it is working properly again.

How can you replace the smart key

Depending on the model of your Kia Sportage, you may have a standard key fob or a smart key. The difference is that the smart key comes with the small blade of a key hidden within it, whereas the standard fob isn't equipped with. Both kinds of key fobs contain a battery inside them that will eventually have to be replaced. Fortunately, it's an easy task that will take about two minutes.

Before you start before you begin, ensure that you're on a flat surface with good lighting and that your Kia is off. Also, remember that there are tiny components inside the fob which could be snagged if not careful.

The first step is to locate the small release button that is located on the back of the lower part of the fob. It can be an oval silver button or a rectangular slot. You can open the key fob by pressing the button.

After the key fob has been removed, you can remove the battery that was in it. The new battery should be a CR-2032 and can be purchased online or at your local auto parts store. After you're done, your key fob should be able to lock, unlock, and start your vehicle even if it's not running.

How do you replace the mechanical key

The 2013 Kia Rio Key Fob Programming key fob is a wonderful option that lets us lock and unlock our car with the click of the button. But like any device it will encounter issues from time to time. There are ways to fix these problems and keep your key fobs in good working order for a long time.

A dead or weak battery is one of the most frequent problems. This could cause your device to stop working or operate intermittently. If this happens then try replacing the battery with a new one.

If this doesn't fix the issue you can try using a standard flathead screwdriver to wedge open the casing of the fob's plastic. Be careful not to scratch any internal components or scratch the plastic. Once open, carefully remove the old battery and replace it with a brand new one.

When the new battery is in, close and then open the doors with the mechanical key (every Kia fob has an emergency mechanical key that can fit into the slot). Test the key fob to verify that it's working correctly. If the key fob isn't working, call a locksmith or dealer to help resolve the issue. To avoid lockouts in the future, ensure you purchase an emergency key that can be able to work with all trunk and door cylinders.