Reasons Your fiat Replacement key cost 500 Key Fob Won't Work

A key fob for the fiat abarth key 500 is a convenient method to unlock the doors and start the car. There are many reasons why the fob could stop working. This includes a dead battery, water damage, problems with the receiver modules, and interference.

This listing is for a NEW replacement fiat 500 stolen without keys Flip Key Remote that appears similar to the Ilco brand. It has to be professionally programmed (click here to search for local automotive locksmiths). This remote includes lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is probably the most common reason for your 500 key fob not working. Modern key for fiat 500 fobs offer an operating range that is limited and must be within a few inches of the vehicle in order to work. If you're far from your vehicle when you press the key fob button the car won't be able to respond, and will display a "Key Fob Not Detected" message in the instrument cluster.

If this happens you need to replace the battery of your coin-cell (Part Number CR2032) with a new battery from a reputable brand like Panasonic Duracell or Energizer. They are usually available at your local hardware store, or online.

After you've replaced the coin cell battery, you can test it by standing in front of your fiat 500x key fob 500 and pressing the buttons. The parking lights should light up and the key fob will operate the lock and unlock switch.

If the fob's key doesn't work after replacing the battery, it may be damaged by water, which prevents it from communicating with the receiver module inside your car. Water damage can occur in a variety of ways, ranging from small splashes to submerging the fob into salt water at the beach. If you suspect your fob was exposed to water, try placing it in a dry rice bag to draw the moisture back out. If this doesn't work, your fob is likely to need to be reset by an experienced auto locksmith or the dealer.

Water Damage

Damage to the water supply can occur if you immerse the fob into the ocean, or wash it in a washer. Saltwater poses a particular risk to the circuit board of the fob that can cause it to short out and eventually die. If you get the fob wet, it's not an ideal choice, but if you drop it into the water in a cup or don't remember to take it out of your pants pocket prior to running the washer and you don't have a chance, don't give in.

Take the battery off first. Before replacing the battery clean the electronic chip with isopropyl or a similar product. Then check the fob to verify if it is working. If the fob doesn't work, it might need to be reset. This is typically done by a professional or dealer auto locksmith.

If the key you have is older and is not programmed for your vehicle You will need to replace it completely. This is a simple procedure that can be carried out by a professional locksmith for automotive use. The locksmith will require the key cut to match your car's ignition. They'll also need to reprogram the fob in the system of your car. This is a low-cost and quick procedure that can be completed on the same day.

Receiver Module Issues

One of the most common reasons your 500 key fob won't be functioning is because it's out of range. The remote typically has 30 feet of range or less, and if it's too far from your vehicle, it won't respond to your commands. It is possible to solve this problem by moving the remote closer to your car until it responds.

If you've replaced the battery on your coin (commonly known as a "button" or "watch") and the fob isn't working It could be because of an internal circuit board problem. In the majority of cases, reprogramming your fob will resolve this problem. You can find the procedure for the majority of vehicles on YouTube or in the owner's guide.

It is sometimes necessary to replace the metal clips that hold the coin batteries in their place. If they become loose, it can prevent your coin battery from sitting properly, causing your remote to malfunction.

In rare cases the fob might be out of the vehicle's sync because of hardware or software problems. You can fix this issue by visiting your local dealer or auto-locksmith to reprogram your key fob. In certain instances they may have to reinstall the program in your body control module, as well.

Interference

In addition to a dead coin battery The key fob might not be able to receive or transmit signals due to interference. This could happen if the key fob is near an electronic radio transmitter (cell phones, radar detectors) or another source of electromagnetic radiation. Other reasons the key fob could not function include a poor connection to the buttons or the internal chip or water damage.

If your key fob suddenly stopped working, or you've tried everything at home to fix it (e.g. It could be a defective 500 receiver module in the event that you've tried replacing the battery, reprogramming, and using an alternative key fob. The receiver module, which is located under the dashboard, picks up radio frequency signals from your key fob. It converts them to electronic commands that the vehicle interprets.

Fortunately, there's an easy method to reset all of the on-board systems in your 500 keys, including the key fob. Disconnect the battery of 12 volts for about 15 minutes, by removing the negative cable first then the positive cable. Then, reconnect the battery. This will remove any remaining electric current, and also restart the car's computer. This will help you get your key fob to function again. If the issue persists, you should speak with an expert technician. They will be able to diagnose the exact cause of your problem.