how to get a new subaru key fob to Change a Subaru Spare Key

When you lose your Subaru car key, contact a locksmith. Locksmiths can usually cut you keys at a lower cost than the dealer.

Subaru car keys are usually either smart "push-to-start" fob remote keys or simple metal keys. The Fob keys have a chip inside and must be reprogrammed.

Keyless Entry System

The key fob can be used to lock and unlock your reprogram subaru key remotely. It can also open the trunk of your car or the lift gate. These remotes use a keypad in your car to connect to your vehicle's computer.

Subaru models offer a little known feature called PIN Code Access. You can make a custom number sequence to start and open your vehicle. If you own a more recent Subaru Forester, Outback, Crosstrek, WRX, WRX STI, or Impreza which came with this feature, consult your owner's manual to see how to get replacement subaru key to utilize it.

It's possible that the battery inside the key fob is dying. The first thing to ensure is that it has fresh batteries and you can accomplish this with a portable remote tester or a basic multimeter from your garage.

The next step is to remove the transmitter circuit board from the key fob and examine it. It will have one or two sets of eight-digit numbers, so note down the first set so you will be able to remember it later. Once you've done that then put the key fob back together and you'll be ready to program it at home. The procedure for programming is different based on the model and year of your vehicle however it's generally easy enough to do by yourself.

Key Fobs

Subaru's newest models are all equipped with key fobs that don't just unlock your doors and activate your lights, lock your gas cap, and even start your car. That last trick is especially helpful if you've been at the gas pump only to find that your car won't start because the key fob battery was dead.

It is likely that your Subaru's key fob, regardless of whether it's brand new or old it is able to be replaced. Remember that some of the modern models, with their top-of-the-line technology, may require an appointment with a dealer. With a little effort and time, you can make your own key fob replacement.

Start by examining the circuit board for the transmitter inside your key fob (instructions to open the case should be included in your owner's handbook). There should be one or two serial numbers that have 8 numbers each. Keep the first set of numbers handy for later references.

Then, get into the driver's seat. Close all the doors. Turn the key to start your vehicle before turning off after 10 turns. Press the lock button on your key fob and open the door to ensure that all doors function properly. After that close the door, and remove the key from the ignition. You should hear the chime from your car to indicate that the key fob has been programmed.

Ignition System

If your Subaru keys aren't working as they should, it could be due to the fact that the battery is dead. You can replace the battery for your key fob on your own if you are familiar with the procedure. A replacement battery is cheap and fairly easy to find. If the key fob doesn't respond to your commands it may be due to a different issue. To find a spare, it's best to visit an authorized dealer. They'll ensure that the key is a genuine Subaru key that's in warranty. They'll also program it to your vehicle. This is a lot easier and safer than buying an aftermarket one from a website.

The dealer will also cut keys for you provided you provide your VIN number and as proof of ownership. The information provided will be used to identify the new key so that it is accepted by your immobilizer. This procedure is more complicated than cutting a new one, and the dealer will generally charge more for this service.

Once the new key has been programmed, it is possible to switch it over to the working key. It will only take you five seconds to insert the new key, so make sure to keep your working key close to the ready. You can remove the key after the security light has been off and you've tested it.

Battery Replacement

One of the most important characteristics that make Subaru fobs so valuable is their ability to switch on your car's power windows and sunroof at the touch of the button. However, the battery inside the Subaru key fob was not designed to last forever and will eventually need to be replaced. This short guide from Capitol Subaru will help you to replace the battery yourself.

You'll have to find the small gap that separates the front and back of your keyfob. With a small flathead screwdriver you can pop this seam wide to reveal a small compartment that houses the battery. Remove the battery that was in it, and then replace it with a fresh one, making sure that it is facing the correct side up. Once everything is reassembled and in place, you can use your new key fob to lock or unlock your vehicle without difficulty!

It's always best to have an extra set of keys on hand in case you've lost yours or it's not working properly. You can purchase a replacement key from your local dealership or get it cut by locksmiths. Whatever you choose, it's essential to get your key fob functioning properly as soon as you can so that you can drive in a safe manner!