Reasons Your fiat panda key fob 500 Key Fob Won't Work

A key fob with the fiat 500 number is a convenient way to unlock the doors and start the car. There are a variety of reasons why the fob may stop working. These include a dead battery, damage how to unlock fiat 500 boot without key the receiver module, water issues, or interference.

This listing is for a NEW replacement fiat punto remote key price Flip Key Remote that is similar to the Ilco brand. It needs to be professionally programmed (click here to search for local automotive locksmiths). Includes lock, unlock, and trunk buttons.

Dead Coin Battery

The most frequent reason why your 500 key fob will not function is the battery is dead. Modern key fobs come with a limited operating range, and must be within only a few feet from the vehicle to function. If you are further away from your car and push the keyfob button it won't respond and display the message "Key Fob Not Detected".

If this happens, replace the battery in the coin cell (Part number CR2032) with a new one from a trusted brand like Panasonic, Duracell, or Energizer. You can find them in your local hardware store or online.

After you've replaced the battery in the coin cell You can test it by standing close to your fiat key fob replacement 500 and pressing the buttons. The parking lights should blink and the key fob will operate the lock and unlock switch.

If your key fob doesn't work even after replacing the battery, there may be water damage that has prevented it from communicating with the module inside your vehicle. Water damage can happen in a number of ways, ranging from small splashes to submerging your fob in salt water at the beach. If you suspect your fob has been exposed to water, try placing it in a dry rice bag to pull the moisture out. If this doesn't work your fob is likely to need to be reset by a professional auto locksmith or dealer.

Water Damage

Water damage can occur when you submerge the fob in the ocean, or wash it in a washer. Saltwater can cause the circuit board to short and then cease to function. It's not good to soak the fob in water however, don't give it up when you accidentally drop it in the water or don't remove it from your pocket.

First, remove the battery from the fob. Clean the electronic chip using isopropyl alcohol or a similar product and then dry it completely before replacing the battery. Check the fob to check if it's functioning. If the key still doesn't work, it may need to be programmed again. This is usually done by a dealer or professional auto locksmith.

If the key is more recent and was not programmed to your vehicle It will most likely need to be replaced completely. A professional locksmith for cars can carry out this simple task. The locksmith will have to cut the key to match the ignition of your car. The locksmith will also have to program your fob into the vehicle's system. This is a simple and inexpensive process that is usually completed on the same day.

Receiver Module Issues

The 500 key fob you have may be inoperable because it's out of range. The remote typically has a range of 30 feet or less and if it's far away from your car it will not respond to your commands. It's easy to solve this problem by moving the remote closer to your vehicle until it responds.

If you've replaced your coin battery (commonly known as"button" or "button" or "watch") and your fob still won't work, it could have an internal circuit board problem. Reprogramming your fob can resolve this problem. You can find the instructions on how to get a replacement key for fiat 500 to do this for all automobiles by searching YouTube or reading the owner's manual.

It is sometimes necessary to replace the metal clips that hold the coin batteries in place. If they loose tension, it can stop your coin battery from sitting properly, causing your remote to malfunction.

In rare instances, the fob can become out of alignment with your vehicle because of software or hardware problems. This issue can be fixed by visiting your local dealer or auto-locksmith to reprogram your key fob. In certain instances it is possible that the software will need to be reinstalled in your body control modules.

Interference

Interference can also cause the key fob not to receive or transmit the signal. This could occur if the key fob is located near a radio transmitter (cell phones or radar detectors) or any other source of electromagnetic radiation. Other reasons the key fob might not function include a weak connection to the buttons and internal chip or water damage.

If your key fob suddenly stopped working, or you've tried everything at home to solve the issue (e.g. battery replacement, reprogramming and using the spare key fob, you might have a defective receiver module on your 500. The receiver module is situated under the dash and receives the radio frequency signals from the key fob. It transforms the signals into electronic commands that are then interpreted by the vehicle.

Luckily, there is an easy way to reset all on-board systems in your 500 keys, including the key fob. Disconnect the 12 volt battery for about 15 minutes, by disconnecting the negative cable first then the positive cable. Reconnect the battery. This will remove any residual electricity and restart the car's computers. This can help you the key fob to function again. If the problem persists you should seek the advice of an expert technician. They will be able diagnose the root of any problems.