How to Replace a kia keys made near me Sportage Replacement Key

The key of a lot of kia carens key fob models has an entry system that is keyless into. The key functions like the remote control and can be exchanged by a Kia dealer.

Key fobs may stop working due to a variety of reasons, including the battery of the coin is dead worn buttons signals, water damage, signal interference and a faulty receiver module. Here are some tips on how you can get your Kia Sportage replacement key working again.

How to replace a remote key or a smartkey?

If your Kia comes with an intelligent key, remote key push-to-start key, or a regular non-transponder steel key, the battery in these keys will eventually need replacing. This is particularly relevant if your vehicle displays a message indicating that the smart or remote keys have low battery power.

Luckily, it's a relatively simple process. In order to replace the key fob battery take the mechanical key from the slit at the back of the key fob and remove the cover. A small screw will be located inside the key fob, which holds the battery in the correct position. Remove the old battery by removing the screw with a small screwdriver. Insert the new battery and close the gap on the key fob.

Test the key fob by pressing the lock and unlock buttons. If the doors unlock and lock in the same way, you're good to go! You can now utilize Kia's hands-free lock/unlock function whenever your fingers get chilly or you need to do some errands in Brandon.

Note: Some keys may require to be programmed (transponder chips or smart keys). This requires a specific programming machine that only the dealer or locksmith can access. Other keys (non-transponder metal keys) do not require programming. If your key requires to be reprogrammed, you must be aware of the key code printed on the tag that identifies the key and save the number in a secure place.

How to replace the battery

If your Kia key fob isn't responding when you press the lock or unlock button on the fob, it is a good indicator that the battery needs to be replaced. A low battery could cause other issues like the check engine light flashing on or a delay in cranking the engine. Fortunately replacing the battery on the key fob is a relatively simple DIY project that requires only a few basic tools.

Make sure you turn off your vehicle and shut all doors before you begin. Locate the small metal or plastic piece at the bottom of your key fob, and move it until a metal key slips out. The key can be inserted into the driver door handle to unlock your car.

To replace the key fob's battery, remove the rear cover and use a plastic bar tool to release the latch holding the black negative battery cable. Remove the old battery, and then align the new one so that the "+" positive side is facing you, while the "-" negative side is facing the fob's metallic electrical contacts. Avoid using too much force when pushing the new CR2032 into position to avoid damage or bending the metal contacts.

Once the new battery has been installed, turn the key fob off and on in the ignition until the door locks cycle. You can then test your kia replacement key fob's keys fob to ensure it's working properly.

how to open kia car key to replace a smart key

Depending on the model of the Kia Sportage, you may have a standard key fob or a smart key. The difference between the two is that the smart fob has a small mechanical key blade that is hidden inside, while the standard key fob does not. Both key fobs are equipped with a battery that will eventually require changing. Fortunately, it's a fairly simple process that takes just two minutes.

Before you start it is essential to make sure that you are on a flat surface with enough lighting and that your Kia is turned off. Also, keep in mind that there are tiny pieces inside the fob which could fall out if you are not cautious.

The release button for the small size is located on the lower backside. It's either an oval or circular slot. You can open the key fob by pressing the button.

Once the key fob is removed, you can remove the old battery. The new battery should be a CR-2032 and can be purchased online or at your local auto parts store. Once you're done, your key fob should allow you to lock or unlock and start your vehicle even if it's not running.

How do I replace the mechanical key?

The Kia key fob is an amazing feature that lets us lock and unlock our car with the touch of an button. But like any device it will encounter issues from time to time. There are ways to resolve these issues and ensure that our key fobs are in good condition for the long term.

A dead or drained battery is among the most frequent problems. This can cause your device to stop working or operate intermittently. If this happens you should replace the battery with a fresh new one.

If this does not solve the issue, try using a flathead screwdriver standard to wedge the fob's plastic casing open. Be careful not to harm any internal components or scratch the plastic. After the battery has been removed and replaced with a new one.

Close and open the door with the mechanical key. (Every Kia fob comes with a spare mechanical key which will fit into the slot). Test the key fob and check that it's functioning properly. If the fob still not working, contact an expert locksmith or dealer to help resolve the problem. To avoid lockouts in the future, ensure you have an emergency key that will work on all door and trunk cylinders.