Replacing uPVC Window Handles

Switching the handles of windows made of upvc is an easy task. It is essential to make sure that the new handle is fitted into the spindle cutout of the window mechanism.

If you follow the steps below the handle of any cockspur will fit on most windows. The step height of the handle is important.

What to Look For

As time passes, uPVC handles on many windows in the UK may begin to show signs of wear and tear. When this occurs, the window handle may become loose or difficult to operate, which makes it necessary to replace it. Anyone who is familiar using a basic hand tool can complete this relatively simple job.

The first thing to do is ensure that the handle is securely fixed to the window frame and is in a position that is open. The next step is to find the fixing pins or screws that hold the handle in the position it is in. These are usually located on the inside of the handle. They can be removed with the screwdriver and pliers.

Once the handle has become loose and sagging, it can be removed from its hinges by gently pulling it off. Then, you will need to locate a new handle in the same style and size. This can be done in an online store or in a DIY store. The process should take only five minutes and a screwdriver is all you need.

The most important thing to consider when replacing a uPVC window handle is the step height. This is the distance from the base of the handle to where it rests on the window frame. It is generally an accepted measurement, however it is essential that you determine the step height of your current handle prior to ordering a new one.

There are several sizes depending on the type of handle. Inline handles for uPVC windows typically have lug centres of 31mm, and there are also cockspur handle types that have 43mm centres. Tilt and turn handles are often used on windows made of uPVC, and they come with a unique design that allows windows to be tilted in for ventilation and turned to open the window completely.

The most common cause of breakage in uPVC handles is that they crack inside rather than breaking off from the base section. This can make it difficult to open. It is essential to make sure that any replacement handle has the same spindle as the original one.

Remove the handle that was previously used

Incorrectly fitted or damaged window handles for bifold doors could cause double-glazed windows to open and close in a way that isn't correct and may result in them getting stuck. There are a variety of reasons for this including general wear and tear, or corrosion of the metal handle. In these cases it is essential to replace the upvc sliding door handle window handle as promptly as you can to prevent further damage or loss of function.

One of the first steps that you should do when replacing the handles on your windows made of upvc is to remove the old handle from the window. To do this, start by getting rid of the screw that is encased when the handle is in its closed position. This will reveal a screw and once removed, you can then begin to remove the handle. It is possible to make the task easier by using an electric screwdriver.

You should also be aware that screws can be hidden under caps made of plastic. It is best to remove the covers with a Stanley knife. After the handle has been removed, examine the square cut out at the handle's base to make sure that the new window lock handles will work with it. This is crucial as you'll need to measure the length of the spindle on the old handle to make sure it is in line with the size of the window mechanism and handle spindle cut out.

There are three kinds of upvc handles: Espag handles with a central screw that can be turned either left or right, Cranked handles with two screws, and Spade handles which have arms that are flat and can be used either side of the windows made of upvc. It is simple to replace the handle once you have identified one that is suitable. Just screw it into the frame, and ensure that the spindle is inserted correctly into the lock mechanism. After that the handle should be secured to the window frame and your replacement window handle window handles made of upvc should be secure.

Take a look at the Spindle

If you have to replace a handle made of upvc that has fallen, it's likely that the spindle that holds it in place is damaged or is loose. In some cases you can tighten the spindle with pin or screw. In other instances, it may require replacement completely. There are many types of upvc window handles. There are three kinds of handles: inline espagnolette tilt-and-turn, and cockspur. Each handle type is installed and replaced in a different way.

It is important to measure the current handle before buying a replacement. This will ensure that the new handle is the right size and fits within the window. All handles are measured according to industry standards, so it is easy to identify the correct size.

To measure the handle's size, turn the window to the open position. Then, you should be able see the size of the screw or pin that secures it. Then, use a tape measure or ruler to determine the length of the spindle. Once you know the length of the spindle you can buy a new one that is the same length.

When purchasing a replacement, it is important to consider the step height of a window handle made of upvc. The step height is measured from the base to the point where the handle is placed on the frame. Typically, this will be around 21mm for uPVC windows or 9mm for aluminum. To make sure that the new handle will fit the gap, drop something into the gap to see the distance it will go before meeting an obstruction.

Cockspur handles usually have different backset heights depending on the type of window they are placed in. Inline Espag handles come with a standard height of 43mm centre to centre (2 fixing points). Cockspur handles have different backsets, based on the window they are located in. This is because they have a spur that extends from the handle and locks over a cockspur wedge striker plate.

Install the new handle

After you've chosen the new handle, make sure it is aligned with the holes for screws on the victorian door handle. Secure it using the screws provided. If you're replacing the latch lever, it can be installed similarly to the door handle. After that, attach the door handles victorian trim to hide the mounting screws.

Tips: To remove the metal head from a wooden wedge, place the handle on the floor so that its wide end is level with the ground. Then, use a hammer and tap the narrow end. Be careful not to damage the handle or spindle.