How to Replace a Kia Sportage Replacement Key

The key on many kia keys made models comes with an entry system that is keyless into. This key is similar to the remote control, and can be exchanged with a Kia dealer.

Key fobs might stop working due to a variety of reasons, including an empty coin battery, worn buttons, signal interference, water damage, and a defective receiver module. Here are some helpful tips to assist you in getting your Kia key fob that is a replacement for the sportage again.

How do you replace the remote key or smart key

If your kia picanto Key programming comes with an intelligent key, remote key push to start key, or a standard non-transponder key made of metal, the battery in these keys will eventually require replacing. This is particularly the case if your car shows a message that states the smart or remote keys aren't powered.

It's a simple process. To replace the battery of the keyfob remove your mechanical key from the slot at the back of the fob. Then, pull the cover open. Inside the key fob will be tiny screws that hold the battery in its place. Take out the old battery by unscrewing the screw using the help of a small screwdriver. Install the new battery and close the slit on the key fob.

Test the key fob by pressing the lock/unlock buttons. You're good to go in case the doors lock and unlock as expected. You can now take advantage of the Kia's hands-free lock/unlock feature when your fingers start to get cold or you need to make errands in Brandon.

Note: Some key fobs (transponder chip or smart keys) may need to have their programming completed. This requires a machine for programming that is available only to the locksmith in the automotive or dealer. Other keys (non transponder keys made of steel) are not required for programming. If you're required to reprogramme your key, you'll have to note the key code's number on the tag for the key code.

How to replace the battery

If your Kia key fob isn't responding to pressing the lock or unlock button on the fob, this is a signal that the battery should be replaced. A low battery may also cause other issues, such as the check engine light coming on or delayed cranking of the engine. It is quite simple to replace key fob battery with just the use of a few tools.

Be sure to turn off your vehicle and shut all doors before you begin. Find the small, metal or plastic piece at the bottom of the key fob. Jiggle it until the key pops out. The key can be put into the driver door handle to unlock your car.

To replace the battery on the key fob, you must remove the cover on the rear. Use a pry tool to loosen the latch that holds the black negative cable. Remove the old battery and orient the new one in a way that the "+" positive side is facing you, while the "negative" negative side is facing the fob's metal electrical contacts. Avoid using too much force when pushing the new CR2032 into place to avoid damaging or breaking the metal contacts.

Once the new battery has been installed after which you turn the key fob off and on in the ignition until the door locks cycle. You can then test the 2015 kia soul key fob's Key fob once more to ensure it's working as intended.

How to replace the smart key?

You could have a standard keyfob, or a Smart Key based on the model of Kia Sportage. The smart key comes with an embedded mechanical key blade, however, the standard key fob does not. Both key fobs have batteries that eventually require replacement. It is a simple process which takes just two minutes.

Make sure you turn off your Kia and be on a flat well-lit and well-lit area before you begin. Keep in mind that there are small parts inside the fob which could fall out if not cautious.

The small release button is located on the lower backside. It's either an oval or circular slot. You can open the key fob by pressing the button.

Once you have the key fob opened it is easy to remove the old battery, and replace it. The new battery should be a CR-2032 and can be purchased online or at a local auto parts store. After you're done, your key fob should be able to lock and unlock your vehicle, even if it isn't running.

How do I replace a mechanical key

The Kia keyfob is an excellent convenience, allowing us to lock or unlock our car simply by pressing a button. But like any device there are issues with it at times. Luckily, there are steps that can be taken to fix these issues and keep our key fobs in good working order in the long run.

One of the most frequent problems is a low or dead battery. This can cause the device to stop working completely or to work intermittently. If this happens, try replacing the battery with a new one.

If this doesn't fix the issue Try using a standard flathead screwdriver to wedge open the casing of the fob's plastic. Be careful not to damage internal components or scratch the plastic. Once the battery is opened, carefully remove the battery you have been using and replace it with a new one.

Close and open the door using the mechanical key. (Every 2013 kia rio key fob replacement fob comes with a spare mechanical key which will fit into the slot). Test the key fob to confirm it's working as intended. Contact a dealer locksmith to address the issue in the event that the key fob is not working. To avoid a lockout in the future ensure you have an emergency key that will be able to work with all door and trunk cylinders.