24 hour boarding up service near me up windows and doors (he has a good point) Before a Storm Hits

Insuring your windows and doorways before an event can give you an effective protection against damage. To do this, you'll should have a few items on the go.

Take measurements of the height and width of the window including the frame (not the trim or masonry surrounding the window). Keep these measurements in mind so you don't forget.

Preparation

It is recommended to put up a board up your windows and doors before the occurrence of a natural or stormy weather. This will prevent property damage and reduce the loss of life. Boarding up windows requires an extensive amount of preparation, including purchasing and measuring plywood boards, and determining the exact size of each window to be covered. It also takes time to cut the boards and then install them properly. Fortunately this can be simplified by beginning the preparations as soon as you hear of a possible storm forming in your area. If you do this you will avoid a stressful last-minute rush and make the process much easier for yourself and your staff.

Begin by listening to forecasters for weather and following guidelines issued by your local government. The earlier you begin the process, you'll be able to gather the materials and store them without being overwhelmed by an approaching storm. Depending on the severity of the event, you may need huge quantities of plywood to cover your windows. Use a tape measure to determine the height and width for each window opening. Make sure to take into account the framing or trim around each window as well as any extended sills if applicable.

Next, calculate the size of the plywood sheets you require by dividing your window's total width and height by two. If your window is wide of 16 inches, the thickness of each sheet is 8 inches. If your exterior is made of wood drill pilots holes into the plywood sheet to ensure it is aligned with the window frame below. This will reduce the possibility of splitting when you screw in the screws.

If you have a larger window than a single sheet of plywood can handle cut two sheets plywood that are half as large as the window you wish to cover. Then place them side by side on the wall. Cut a piece of 2 by 4 inches (5.1 x 10.2 cm) of lumber to the length of the connecting edge between the sheets of plywood and then place it on the top of the seam. Then then, drive 2.25 in (5.7 cm) screws through the bracing and into the plywood sheet to join them together.

Materials

To ensure security and safety For security and safety, boarding up service near me windows and doors must be done using only solid materials that will not break under pressure or split in high winds. The most commonly used material to encase windows is plywood, which is affordable easily available and simple to work with. It is important to select plywood that is specifically exterior grade (CDX) to ensure strength and is free of knots and warping. Storm shutters, also known as hurricane shutters, are a more robust option. They can be put in over existing windows and offer better protection against glass breakage and storms.

Once you've determined the location of the window openings, measure the height and width of each to determine the amount of plywood you'll need. Then make use of the power drill to drill pilot holes in the plywood sheets at two-inch intervals around each window. Before attaching the plywood, you must identify and mark the locations of studs on the wall to ensure that the boards are anchored securely. If your home has wood siding, look for nailheads that might indicate the location of studs. You could also use your drill to determine the studs' locations. The screws should be driven into the framing, not the sheathing or trim. A plywood panel that is attached to these materials may be a danger to safety during severe winds.

If the size of your window is too big for a single piece of plywood, cut two separate pieces that are each half the size you need and join them using 2 by 4 inch lumber. Label each plywood piece so that you know which window it will be covering.

To affix the plywood panels to the wall, make use of corrosion-resistant screws that are sufficient in length to penetrate both the sheathing and the studs. To secure the plywood panels to the wall, use corrosion-resistant screws that are long enough to get through both the sheathing and the studs.

You should also think about installing polycarbonate security glass similar to DefenseLite on your primary windows. These transparent shields are bonded to existing glass and shield your windows and door. They are virtually indestructible and can deter burglars from attempting to break into your home.

Installation

If you live or plan to move to an area which is susceptible to hurricanes and you are worried about the storm you should consider emergency boarding up cost up your doors and windows. This project can be completed quickly and efficiently, but only if the boards are cut, measured and labeled prior to the storm arrives.

You'll also require other tools, such as drills (or a hammer and nails if you don't have the power drill) as well as tape, a saw, a level, gloves and safety glasses. It's a good idea apply sealant to the plywood in order to make it waterproof.

Begin by measuring each window opening's size and height. Then cut the plywood sheets to fit inside the frames. It is best to do this on the spot, as it gives you more control over the exact dimensions of the plywood.

Cut the boards to the desired size using a circular or track saw. After installation you'll need to sand all of them. Once you've put your boards in place, screw 3 inch stainless steel hanger bolts into the framing studs around each window. Use washers on each bolt, and wings nuts to anchor them. Make sure that each screw penetrates the studs at least two inches to ensure that the board is strong enough to withstand high winds.

If you're building with concrete blocks, you can join the plywood using pan head screws galvanized and that are driven into the overlapping edges of the panels into bricks or cinder blocks. It is also necessary to drill pilots into the masonry before screwing corrosion resistant screws into the holes. This project can take three hours for each time period. It is crucial to begin as soon when an alert for hurricanes has been issued. This will give you enough time to complete the project before the storm hits.

Maintenance

If you're a homeowner or business owner, you should have the required materials to board up windows and doors in advance of a severe storm. This will allow you to avoid costly repairs and protect your home from further damage caused by rain, wind, flying objects and other factors.

The right materials will make the boarding up process faster and easier to complete. The key is to precisely measure the dimensions of the windows you'll must cover. This will ensure that the plywood or OSB fits snugly and won't be able to fall off easily. If you're using plywood, be sure to use exterior-grade sheets and consider adding a protective finish.

Once you have the OSB or plywood taken measurements, mark the locations where screws will be inserted into the board. Then, you can use a drill to pre-drill holes in the plywood at intervals of 12 inches. Then, you can use hanger bolts to anchor the boards in an emergency boarding up service or disaster situation. When the storm has passed and the local authorities have given the all-clear, take out the bolts but keep them in case of a need in the future.

The next step is to install the plywood panels on top of the windows. Be prepared to work in pairs. If you're using wood, make sure to sand down the edges to ensure they're smooth and won't scratch your paint or trim. Then, attach the frame to the plywood using corrosion-resistant screws that fit into the pilot holes. If your home is lined with shingles made of vinyl it is best to attach the plywood to the shingles rather than the wood framing beneath.

A window that is boarded up can be used to stop burglars. Burglars are more likely take aim at a structure that has a locked or broken window. They're also more likely to attack a store that's been fenced off than one that isn't. This is something that business owners in retail should take very seriously.